Emergency maintenance and handling methods for driving faults:

1.進、出水軟管破裂

1. The inlet and outlet hoses are broken

破裂不大時，可用涂有一層肥皂的布將漏水處包扎好；如破裂較大時，可將軟管破裂處切斷，在中間套上一個竹管或鐵管，并用鐵絲捆緊。

When the rupture is not significant, a cloth coated with a layer of soap can be used to wrap up the leaking area; If the rupture is significant, the hose can be cut off at the point of rupture, and a bamboo or iron pipe can be placed in the middle and tied tightly with iron wire.

2.風扇皮帶斷裂

2. Fan belt broken

可把斷了的皮帶用鐵絲扎好或采用開開停停的辦法把車開走。

You can tie the broken belt with wire or use a stop and start method to drive the car away.

3.螺孔滑扣

3. Screw hole sliding buckle

螺孔滑扣會導致漏油或連桿松動，使其無法工作。這時可將原螺桿用錘子砸扁，使其兩邊膨脹增大再緊固好，但不可多次拆卸，待下次保養時修理。

Screw hole sliding buckle can cause oil leakage or loosening of the connecting rod, making it unable to work. At this point, the original screw can be flattened with a hammer to increase its expansion on both sides and then tightened, but it cannot be disassembled multiple times and will be repaired during the next maintenance.

4.油箱損傷

4. Fuel tank damage

機動車在使用時，發現油箱漏油，可將漏油處擦干凈，用肥皂或泡泡糖涂在漏油處，暫時堵塞；用環氧樹脂膠粘劑修補，效果好。

When a motor vehicle is in use and finds oil leakage in the fuel tank, it can be wiped clean and coated with soap or bubble gum to temporarily block the oil leakage; Repairing with epoxy resin adhesive yields good results.

5.油管破裂

5. Oil pipe rupture

油管破裂時可將破裂處擦干凈，涂上肥皂，用布條或膠布纏繞在油管破裂處，并用鐵絲捆緊，然后再涂上一層肥皂。

When the oil pipe ruptures, the ruptured area can be wiped clean, coated with soap, wrapped with cloth or tape around the ruptured area, tied tightly with iron wire, and then coated with a layer of soap.

6.油管折斷

6. Oil pipe breakage

油管折斷時可找根與油管直徑相適應的膠皮或塑料管套接。如套接不夠緊密，兩端再用鐵絲捆緊防止漏油。

When the oil pipe is broken, a rubber or plastic pipe that is suitable for the diameter of the oil pipe can be used to connect it. If the fitting is not tight enough, tie both ends tightly with iron wire to prevent oil leakage.

7.缸蓋出現漏洞而漏油、漏水

7. Leakage of oil and water due to cylinder head leakage

可根據漏洞大小，選用相應規格的電工用保險絲，用手錘輕輕將其砸入漏洞內，即可漏油、漏水。

According to the size of the vulnerability, appropriate specifications of electrician fuses can be selected, and gently smashed into the vulnerability with a hammer to eliminate oil and water leakage.